Analisis Pengendalian Kualitas Hasil Pengelasan Bengkel Welding HO & AO di PT. A Menggunakan Metode Six Sigma dan  New Seven Tools

Nurul Amalliyah; Isna Nugraha

doi:10.37090/indstrk.v9i2.2058

Authors

Nurul Amalliyah Universitas Pembangunan Nasional "Veteran" Jawa Timur
Isna Nugraha Universitas Pembangunan Nasional "Veteran" Jawa Timur

DOI:

https://doi.org/10.37090/indstrk.v9i2.2058

Abstract

PT A is a state-owned maritime manufacturing company that produces ships. There are a number of workshops that support the production process, one of which is the HO & AO Welding Workshop. The problems that occur in the HO & AO Welding Workshop are 3 types of defects that are often found in Welding results in the form of Spatter, Undercut, and Pin hole. This study aims to improve quality and propose improvements that can be made to reduce defects in the HO & AO Welding workshop at PT. A. Therefore, it is necessary to carry out quality control with the Six Sigma method and New Seven Tools. Based on the results of the study, it is known that the DMAIC (Define, Measure, Analyze, Improve, Control) analysis with the results obtained through testing the quality of Welding products resulted in 548 failure units, a DPMO value of 49289 and then converted to a sigma level of 3.15 which indicates that the sigma level is at the average of the Indonesian industry. It can be explained that the possibility of damage is 49289 for a million production. And the main defect-causing factors have been successfully identified through the application of New Seven Tools which include human, material, method, machine, and environmental factors. Therefore, PT. A is advised to implement improvement recommendations to reduce product defects.

Keywords: Defect, New Seven Tools, Quality, Six Sigma, Welding

Downloads

Download data is not yet available.

References

Arera, A.F. and Suseno (2023) ‘Analisis Pengendalian Kualitas Produk Giboult Menggunakan Metode New Seven Tools Di Pt Aneka Adhilogam Karya’, Jurnal Teknik Informatika dan Elektro, 5(2), pp. 114–126.

Aziza, N. and Setiaji, F.B. (2020) ‘Pengendalian Kualitas Produk Mebel Dengan’, Engineering and Sains, 4, p. 28.

Bakhtiar, A. et al. (2020) ‘Penerapan Metode Six Sigma di PT Triangle Motorindo’, Opsi, 13(2), p. 114.

Damayanti, A.P. and Aziza, N. (2024) ‘Six Sigma Dalam Perspektif Akuntansi Manajemen: Peningkatan Manajemen Biaya Strategis dan Pengendalian Kualitas Produk’, Owner, 8(2), p. 1770.

Fajar, D.P. and Andesta, D. (2023) ‘Evaluasi Mutu Pada Proses Pengelasan Menggunakan Metode Old dan New Seven Tools di PT . XYZ’, VIII(4), pp. 6842–6855.

Firmansyah, I. et al. (2021) ‘Penerapan Metode Six Sigma untuk Menurunkan Terjadinya Keterlambatan Informasi Kedatangan Barang ( NOA ) dalam Kegiatan Impor’, Jurnal Sistem Transportasi & Logistik, 1(2), p. 80.

Firmansyah, R. and Yuliarty, P. (2020) ‘Implementasi Metode DMAIC pada Pengendalian Kualitas Sole Plate di PT Kencana Gemilang’, Jurnal PASTI, 14(2), p. 174.

Hidajat, H.H. and Subagyo, A.B. (2022) ‘Analisis Pengendalian Kualitas Produk X Dengan Metode Six Sigma (DMAIC) Pada PT. XYZ’, Jurnal Ilmiah Wahana Pendidikan, 8(9), p. 235.

Kistianto, D.G. and Prakoso, I. (2023) ‘Analisis Kualitas Produk Joran Pancing Dengan Menggunakan Metode New Seven Tools (Studi Kasus: PT.X)’, Jurnal Ilmiah Teknik dan Manajemen Industri, 3(1), pp. 68–79.

Lafeniya, S.D.A. and Suseno (2023) ‘Pengendalian Kualitas Produk Kain Grey Dengan Metode New Seven Tools Pada PT Djohartex’, Jurnal Inovasi dan Kreativitas (JIKa), 2(2), p. 48.

Nadiyah, K. and Dewi, G.S. (2022) ‘Quality Control Analysis Using Flowchart, Check Sheet, P-Chart, Pareto Diagram and Fishbone Diagram’, Opsi, 15(2), p. 183.

Nugraha, I. and Aryanti, F. (2024) ‘Implementation of Lean Six Sigma in Improving Quality by Reducing Defective Products in Aqua Mineral Water Gallon Distribution’, 2024, pp. 40–46.

Permono, L., Salmia, L.A. and Septiari, R. (2022) ‘Penerapan Metode Seven Tools Dan New Seven Tools Untuk Pengendalian Kualitas Produk (Studi Kasus Pabrik Gula Kebon Agung Malang)’, Jurnal Valtech (Jurnal Mahasiswa Teknik Industri), 5(1), p. 63.

Pratama, A.T. and Nugraha, I. (2024) ‘Analisis Penyebab Sisa Pipa Produksi Kapal X Menggunakan New Seven Tools Dan FMEA : ( Studi Kasus : PT . KRS )’, Jurnal Pendidikan Tata Niaga (JPTN), 12(1), p. 52.

Rochmoeljati, R. et al. (2023) ‘Analisis Pengendalian Kualitas Produk Kaos PT. XYZ dengan Metode Six Sigma dan Kaizen’, Waluyo Jatmiko Proceeding, 16(1), pp. 481–490.

Somadi (2024) ‘Evaluasi Pengiriman Dangerous Goods: Metode Analisis Six Sigma-DMAIC’, 8(4), p. 777.

Suci, Y.F., Nasution, Y.N. and Rizki, N.A. (2017) ‘Penggunaan Metode Seven New Quality Tools dan Metode DMAIC Six Sigma Pada Penerapan Pengendalian Kualitas Produk’, 9(2), pp. 88–89.

Suhartini, Basjir, M. and Hariyono, A.T. (2020) ‘Pengendalian Kualitas dengan Pendekatan Six Sigma dan New Seventools sebagai Upaya Perbaikan Produk’, Journal of Research and Technology, 6(2), p. 300.

Sutanto, A.D. and Suseno, A. (2024) ‘Identifikasi Cacat Cetak Proses Produksi Kemasan Fleksibel Di Unit Printing PT. ACP Dengan Metode Six Sigma DMAIC’, 8(4), p. 874.

Yosua, Susetyo, A.E. and Susanti, D.A. (2024) ‘Pengendalian Kualitas pada Industri Kerajinan Sarung Tangan dengan Metode Six Sigma dan FMEA pada CV. XYZ’, 8(4), p. 853.

Yunitasari, E.W. and Royanto, P. (2020) ‘Peta Kendali Atribut Untuk Mengidentifikasi Kecacatan Produk Furniture di PT ISI’, Jurnal Teknologi Technoscientia, 12(2), pp. 175–183.