ANALISIS RELIABILITY CENTERED MAINTENANCE (RCM) PADA ALAT BONGKAR MUAT RUBBER TYRE GANTRY CRANE (RTGC) DI PT XXX
DOI:
https://doi.org/10.37090/indstrk.v5i2.357Keywords:
Failure, Maintenance, Rubber Tyre Gantry Crane (RTGC), Reliability Centered Maintenance (RCM), PlanningAbstract
The loading and Unloading operational activities in port often run into obstacle, because happened malfunction occurrence of the equipment used. Failure to operate the equipment has resulted in downtime decreased of company productivity. Therefore, a system is needed maintenance of planning in order to produce the equipment that can be operated optimally. This research was choosen the company PT. XXX which is a company that enganged in the field maintenance of equipments port operational (quayside container crane, rubber tyre gantry crane, gantry luffing crane, and others) the place where the equipment maintenance system, especially the rubber tyre gantry crane (RTGC) which has been done are still a breakdown maintenance and corrective maintenance. The aim of this research is to analyze by method of reliability centered maintenance (RCM) to able to determined the optimal maintenance and it can be predict steps to overcome the damage that might will happen in the next period based on existing data. From data processing and analysis was obtained that the components most frequently damaged on the equipment of RTGC, cause of failure, selection decision and recommendations for maintenance systems are based on Reliability Centered Maintenance (RCM).
References
Daftar Pustaka
Abidin, M. R. (2019). Perencanaan Penjadwalan Perawatan Mesin Wheel Loader Dengan Pendekatan Reliability Centered Maintenance Di Pt. Swadaya Graha (Doctoral Dissertation, Universitas Muhammadiyah Gresik).
Adam, Tommy. Perencanaan Perawatan Mesin Thicknesser Dengan Metode Reliability Centered Maintenance (RCM) Dan Failure Mode And Effect Analysis (FMEA); Studi Kasus: Ud. Den Bagus. Diss. University Of Muhammadiyah Malang, 2019.
Ahmadi, Noor, and Nur Yulianti Hidayah. "Analisis Pemeliharaan Mesin Blowmould dengan Metode RCM di PT. CCAI." Jurnal Optimasi Sistem Industri 16.2 (2017): 167-176.
Alghofari, Ahmad Kholid, Much Djunaidi, and Amin Fauzan. "Perencanaan Pemeliharaan Mesin Ballmill Dengan Basis RCM (Reliability Centered Maintenance)." Jurnal Ilmiah Teknik Industri 5.2 (2006): 45-52.
Amalia, Sinar, Arief Subekti, and Priyo Agus Setiawan. "Perencanaan Kegiatan Perawatan dengan Metode RCM II (Reliability Centered Maintenance) dan Penentuan Persediaan Suku Cadang Pada Boiler Perusahaan Rokok." Seminar K3. Vol. 1. No. 1. 2017.
Ansori, N., Mustajib, M, I. 2013. Sistem Perawatan Terpadu. Yogyakarta : Graha Ilmu.
Ardhi, T. H. (2019). Minimasi Downtime Pada Unit Shore To Ship Dengan Metode Reliability Centered Maintenance (RCM) Di PT. Mitra Sentosa Abadi. JISI: Jurnal Integrasi Sistem Industri, 6 (2), 127-133.
Aufar, A. N., Leksananto, K., & Prassetiyo, H. (2014). Usulan Kebijakan Perawatan Area Produksi Trim Chassis Dengan Menggunakan Metode Reliability Centered Maintenance (Studi Kasus: PT. Nissan Motor Indonesia). Reka Integra, 2(4).
Bangun, Irawan Harnadi, Arif Rahman, and Zefry Darmawan. "Perencanaan Pemeliharaan Mesin Produksi Dengan Menggunakan Metode Reliability Centered Maintenance (RCM) II Pada Mesin Blowing Om (Studi Kasus: PT Industri Sandang Nusantara Unit Patal Lawang)." Jurnal Rekayasa dan Manajemen Sistem Industri 2.5 (2014): p997-1008.
Chandra, Muhammad Rizky Eka Permata. Analisis Keandalan Pada 542 Fn7 Finish Mill 2 Pabrik Tuban 1 PT. Semen Indonesia (Persero) Tbk. Dengan Pendekatan Metode Reliability Centered Maintenance. Diss. Institut Teknologi Sepuluh Nopember Surabaya, 2016.
Denur, D., Hakim, L., Hasan, I., & Rahmad, S. (2017). Penerapan Reliability Centered Maintenance (RCM) pada Mesin Ripple Mill. JISI: Jurnal Integrasi Sistem Industri, 4(1), 27-34.
Dyadem . 2003. Panduan Untuk Failure Mode And Effect Analysis Untuk Otomotif, Dirgantara Dan Industri Manufaktur Umum. Ontario: CRC Press.
Gusti Ngr. Rai Usadha, Valeriana Lukitosari, Roficoh Nur Rohmah.†Analisa Keandalan Pada Peralatan Unit Penggilingan Akhir Semen Untuk Menentukan Jadwal Perawatan Mesin (Studi Kasus Pt. Semen Indonesia Persero Tbk.) Seminar Nasional Matematika dan Aplikasinya, Surabaya, Universitas Airlangga, 21 Oktober 2017
Hakim, Legisnal. "Penerapan RCM Pada Sistem Distribusi Air Di Pdam Pasir Putih Pematangan Barangan Kabupaten Rokan Hulu." Jurnal Aptek 4.2 (2014): 129-140.
Kurniawan, Fajar. 2013 Manajemen Perawatan Industri; Teknik Dan Aplikasi; Implementasi Total Productive Maintenance, Preventive Maintenance Dan Reliability Centered Maintenance. Yogyakarta. Graha Ilmu.
Maulana, Irfan, Akhyar Ibrahim, and Darmein Darmein. "Analisa Kerusakan Komponen Undercarriage Excavator Hitachi Ex200 Pada Pt. Takabeya Perkasa Group Dengan Metode Fmea." Jurnal Mesin Sains Terapan 1.1 (2017): 32-37.
Muhsin, Ahmad, and Ichsan Syarafi. "Analisis Kehandalan dan Laju Kerusakan pada Mesin Continues Frying." Opsi 11.1 (2018): 28-34.
Palit, Herri Christian, and Winny Sutanto. Perancangan RCM untuk mengurangi downtime mesin pada perusahaan manufaktur aluminium. Diss. Petra Christian University, 2012.
Pranoto, Hadi.â€Reliability Centered Maintenance†Mercu Buana Mitra Wacana Media, 2015
Putra, Eko Lisysantaka Rusma. 2011. Artikel Reliability Centered Maintenance (RCM) Https://Www.Scribd.com (diakses pada tanggal 30 September 2019).
Rosih, Akhmad Raunaq, Mochamad Choiri, and Rahmi Yuniarti. "Analisis risiko operasional pada departemen logistik dengan menggunakan metode FMEA." Jurnal Rekayasa dan Manajemen Sistem Industri 3.3 (2015): p580-591.
Saputra, Denny Randiana Firda, Yudi Sukmono, and Lina Dianati Fathimahhayati. "Analisis Reliability Pada Mesin Fan Mill Unit 1 di PT Cahaya Fajar Kaltim." Dinamika: Jurnal Ilmiah Teknik Mesin 10.1 (2018): 1-8.
Soleh, S., Bandriyana, B., Djajono, H. S. W. I., & Mm, I. (2013). Analisis Dan Perancangan Sistem Informasi Preventive Maintenance Dengan Modularity Pada Pt. Multazam Mitra Prima (Doctoral Dissertation, Binus).( 2012-2-00251-Tisi Bab2001)
Sukopriyatno, Adi, Sri Rahayuningsih, and Ana Komari. "Perancangan Penjadwalan Perawatan Mesin Bubut Dengan Metode Reliability Centered Maintenance (Rcm) Di Bengkel Pemesinan Smk Negeri 1 Kediri." JURMATIS: Jurnal Ilmiah Mahasiswa Teknik Industri 1.1 (2019).
Susanto, Agustinus Dwi, and Hery Hamdi Azwir. "Perencanaan Perawatan Pada Unit Kompresor Tipe Screw Dengan Metode RCM di Industri Otomotif." Jurnal Ilmiah Teknik Industri 17.1 (2018): 21-35.
Utomo, R.W. (2018). Perencanaan Perawatan Mesin Pump 107 Dengan Metode Reliability Centered Maintenance (RCM) Di PT. Petrokimia Gresik. Jurnal Energi dan Teknologi Manufaktur (JETM)
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
